Skip to Content

DIY Circular Saw Jig for Perfectly Straight Cuts

Make this simple circular saw jig and every cut will be perfectly straight! Just clamp the jig to your board and slide the circular saw along the fence.

how to make a circular saw cutting jig

Cutting a piece of wood in a straight line seems simple enough. Just follow a line with the blade of your circular saw, right? But as you work your way down the board, the saw takes on a life of its own and you end up with a wonky edge.

By using a simple DIY circular saw jig, you can ensure that your cut will be straight and exactly where you wanted it. It basically turns your circular saw into a track saw, but without the hefty price tag!

This post contains affiliate links for your convenience. Purchases made through these links may earn me a small commission at no additional cost to you. Please visit my disclosures page for more information.

There are several rip cut guides for circular saws on the market, such as the Kreg Rip Cut or the new Accu-cut. But, if you're just starting out with woodworking, the cost can be prohibitive.

Inexpensive guides such as this one have a tendency to bow out in the middle, resulting in a less than straight cut. I own both the Rip Cut and the cheaper version, and I still go back to this very simple circular saw jig I made in my beginner woodworking class.

How to Build a Circular Saw Jig

Materials Needed

Don't forget your safety gear when woodworking! Here are my recommendations for safety glasses and ear protection. No excuses!

Line up the plywood strips with your saw

Cut the plywood sheet into roughly one foot wide strips. There's no need to be exact. Just make sure that one piece is a few inches wider than your circular saw, including the motor.

With the saw unplugged, lift the blade guide up so that the blade is exposed. Place the saw on the larger piece of plywood, matching up the edge of the wood with the side of the blade.

circular saw blade lined up with edge of plywood strip

Line up the other piece of plywood next to the edge of the circular saw base plate.

edge of plywood strip aligned with circular saw base plate

Glue the two plywood strips together

Remove the saw, then draw a line where the two plywood pieces overlap. Remove the top board, and drizzle wood glue all over that side of the board, leaving about an inch clear of the line.

wood glue on bottom plywood strip of circular saw jig

Place the top plywood piece onto the glue, setting it about ½ inch away from the line you drew (towards the glued side). You'll see why later on. Clamp the pieces together, or place something heavy on top, and let the glue dry.

two halves of the circular saw jig glued and clamped together

Trim the jig to the width of your circular saw

You'll notice that the bottom of the circular saw jig isn't even. Once the glue is dry, flip it over and trim off the excess with your circular saw. Don't worry if the edges don't exactly line up. You can sand it down later.

circular saw jig flipped over to show where to cut off excess

Every circular saw has a very slightly different width between the edge of the base plate and the blade, even among identical brands. In my beginner woodworking class, the instructor numbered every circular saw and its corresponding jig. Mixing up the saw and the jig would result in a cut that was slightly off!

Clamp your jig to your work surface, making sure to elevate it with a few scrap pieces of wood so you don't cut into the table. Line up the edge of your saw's base plate with the fence you created, then cut away the edge of the board.

cutting the edge of the circular saw guide to the exact width of the circular saw plate

How to Use a Circular Saw Cutting Jig

Congratulations! You have two pieces of plywood glued together! So now what?

Here's an example. Say you're making this outdoor storage bench out of ¾" plywood. You've marked this particular piece with the line you need to cut, and an 'X' on the waste side of the board.

plywood sheet with cut line and waste side marked

Elevate the board with a few scrap blocks of 2x4 so you don't cut into the worktable. You can also use foam insulation sheets for full support across the entire piece.

plywood propped up on 2x4 boards to prevent cutting into work surface

Place the jig on the cut line, making sure that the saw blade will be on the waste side. Clamp the jig to the board at both ends, and then the board to the worktable so it doesn't move around mid-cut.

circular saw jig clamped to plywood to be cut

Before tightening the clamps, double check that the corner will be square. Place a speed square at the cut line and adjust the circular saw jig if necessary.

checking the circular saw cutting jig for square before cutting

Finally, place the circular saw against the fence. Double check to make sure the clamps aren't in the way of the saw motor, then make the cut. Be sure to keep the saw flat on the circular saw jig and slide it slowly along the edge.

circular saw cutting plywood using a circular saw jig.

Ta da! A perfectly straight cut!

Of course, a table saw would make this cut in a fraction of the time it takes to set up this circular saw jig. But for a beginner on a budget, this is the perfect way to cut sheets of plywood or even dimensional lumber! See, you don't need lots of fancy tools to start woodworking!

Check out these other beginner woodworking tutorials!

Chris ruiz

Friday 31st of March 2017


Here is another way. I like it because you can cut from either side of saw blade.

Take about 16" wide piece of plywood ( or whatever you want the bottom to be my first one i used a very thin quarter inch board and I'm regretting it ....although it is light and easy to work with. In the middle of that piece of plywood however long you want it to be a piece of 4 inch or 3 inch wide white MDF board. The guy whose idea I used said that the MDF board is cut such that it is always perfectly straight and rarely warps or has issues. I believe it is also about 3/4 inch thick so that gives your saw edge a nice high surface to run against. Here's the tricky part. now make sure the MDF board is perfectly square and straight on both sides and both ends. Mark it, with a pencil, on both sides, and then put glue down clapping and insert screws from the top.... Again checking to make sure it's Square after you have set it down on the glue before you Clamp It. Once all that is done and dried then you take your saw and on one side you trim off using the right edge of your saw it on the other side you trim off using the left edge of your saw... for example on mine one side is about 5 inches wide and the other side is about 1 inch wide and in between those two is the MDF board so 5 + 4 + 1 is 10 wide total inches wide.

You can drill a hole in it to hang it up and you can also leave the MDF board on one side hanging off about a half inch so that you have a nice edge to go against when starting pick up the edge early before you get to cutting the board. Now you have the capability of cutting with either side of your song which comes in handy because sometimes it's helpful to have that option

I made one 48" to cut plywood and then I made one 24 inches but I rarely used it so then I made one 12 inches and I use that a lot to cut two by sixes etc. the only tricky part is clamping it when The guide is longer than the piece you're cutting as a clipping from the side


Friday 31st of March 2017

Wow, thanks for describing your set up, Chris! I have some scrap MDF boards left over from shelves I removed that I'll have to try this on!

Rob Simpson

Wednesday 14th of September 2016

Well i always had problems in cutting perfect straight lines using circular saw, Really glad this guide helped me, guys you gotta master the art ! Thanks Vineta :)

The Handyman's Daughter

Wednesday 14th of September 2016

Glad I could help, Rob!

Linda Prin

Wednesday 8th of June 2016

The simplicity of your saw project is very smart! I am such an a rookie when it comes to power tools and since your project outlines so many specifics that make the process easy for me. I probably wouldn't be the best critic of the work, but it proved an easy way to achieve the same cuts for my planter boxes. Thanks for the money saving information and creativity.

The Handyman's Daughter

Wednesday 8th of June 2016

I'm so glad my guide could help! Enjoy your planter boxes!

Michael A. Temple

Monday 18th of January 2016

Thanks for sharing your experience. This DIY Circular Saw Guide is quite helpful. I want to buy some tools for my workshop. I'm still wavering between buying a circular saw and table saw. But my workshop is too small for a table saw so a circular saw is the best choice (with your DIY Circular Saw Guide).

The Handyman's Daughter

Monday 18th of January 2016

I had the same dilemma in my workshop, and the circular saw was the best choice for now. So glad I could help!

Wendi @ H2OBungalow

Friday 9th of October 2015

Super smart idea.. and you're so right, this is a fantastic jig if there isn't room in the budget or space for a table saw! Pinning :)

The Handyman's Daughter

Friday 9th of October 2015

Thanks Wendi!

Comments are closed.